Source-linked homeowner guide9 min read

PID Degradation: Why an Older Array Quietly Loses Output

The system is clean, the inverters report no fault, and production has drifted down over years. One explanation is potential induced degradation, and it has a specific electrical fingerprint.

Last updated:

Reviewed against manufacturer and public agency documentation in November 2026. Educational information, not tax, legal, engineering, electrical, or utility advice.

What PID physically is

Potential induced degradation is a loss of module power driven by the electrical potential between the cell circuit and the grounded frame. Under that sustained voltage, and with moisture present in the encapsulant, charge carriers migrate and build up where they degrade the cell's ability to hold voltage.

The first field observations were published by Pingel and colleagues in 2010, which is where the term was coined. Their controlled test produced a 32 percent power loss after 100 hours at 1000 volts, which shows how severe the mechanism can be under stress rather than how much a typical roof has lost.

What makes a particular array more exposed

  • Higher system voltage means more driving potential. A 600 volt residential string is less stressed than a 1000 or 1500 volt commercial array, but the mechanism is the same.
  • Ungrounded and floating arrays put the most negative potential on the modules at the negative end of the string, which is usually where the worst modules sit.
  • Humidity and heat accelerate it, which is why a coastal Florida roof is a harder environment than a dry one.
  • Encapsulant and glass construction matter. Module makers have reformulated to resist it, so a 2013 module and a 2026 module are not equivalent.

The electrical fingerprint

PID is a voltage and fill-factor problem, not a current problem. Open-circuit voltage falls, low-light performance falls further, and short-circuit current stays close to normal. That combination is what separates it from soiling, shading or a dead bypass diode.

It is also positional. In a floating string the modules nearest the negative end degrade first and worst, so a monitoring platform often shows a gradient rather than a random scatter.

Screening signatures. Only a technician with the right instruments can confirm the diagnosis.

MeasurementTypical PID signatureWhat it rules out
Open-circuit voltageReducedSimple soiling, which barely moves voltage
Short-circuit currentNearly normalShading or a failed string, which cut current
Low-light outputDisproportionately poorUniform heat derate
Position in stringWorst near the negative endA single isolated device failure
Insulation resistanceReduced string-to-groundNothing; this points toward leakage

What can be recovered and what cannot

Recovery depends on which mechanism is at work. Polarization losses and a substantial part of the shunting loss are largely reversible, and the industry does exactly that: a night-time reverse-bias device raises the array to a positive potential relative to earth after sunset and drives the charge back. One commercial example, SMA's PV Offset Box, raises the array to between 400 and 1000 volts to earth and states that regeneration takes roughly half as long as the degradation did.

Corrosion-driven and delamination-driven variants are not recoverable. And recovery is not repair: unless the driving potential or the moisture path is corrected, the loss returns.

  • Reversible in principle: polarization and much of the shunting loss, using night-time reverse bias with manufacturer approval.
  • Not reversible: corrosion and delamination variants, and some permanent low-light loss.
  • Recurs unless the cause is addressed, which is why recovery alone is a maintenance strategy rather than a fix.
  • Requires module and inverter manufacturer approval before any recovery hardware is connected.

What to do with a suspected PID array

  • Pull twelve months of production history and look for a slow decline rather than a step change.
  • Note whether the weak modules cluster at one end of a string in the monitoring view.
  • Rule out soiling, shading and vegetation first, because those are cheaper to test.
  • Ask a service provider for string-level voltage and current comparisons under equal sun before authorising recovery hardware.
  • If recovery is proposed, ask whether the manufacturer approves it for these exact modules and what prevents recurrence.

Frequently asked questions

The screening pattern is reduced open-circuit voltage, poor low-light output and nearly normal short-circuit current, worst at the negative end of a string. Confirming it requires current-voltage curve tracing and electroluminescence imaging, so the test itself is a professional service.

Property-specific next step

Request a Production Review

Send the production history, the system age and the module model. We can review the request and check whether a licensed partner can run the diagnostic tests.

Palm Beach Solar plans and coordinates the project. The selected licensed installation or service partner evaluates, quotes, and performs work under its own contract, licensing, and warranty terms.