Source-linked homeowner guide8 min read

Solar Output Dropped in Summer Heat? Normal Derate vs a Fault

Production falls in July and the graph looks wrong. On most South Florida roofs that is physics, not a failure, and the size of the drop is predictable.

Last updated:

Reviewed against manufacturer and public agency documentation in November 2026. Educational information, not tax, legal, engineering, electrical, or utility advice.

Why heat costs production, and by how much

Solar modules are rated at 25 degrees Celsius cell temperature. Real cells on a Florida roof run far hotter than the air, because the module sits in direct sun with limited airflow behind it. Every degree above 25C costs a fraction of the module's rated power.

The fraction is the temperature coefficient of Pmax, published on every module datasheet. Across current modules the range runs from about -0.24 percent per degree on premium heterojunction modules to about -0.36 percent on older poly and PERC products. Mainstream N-type TOPCon modules, which dominate 2025 and 2026 installations, sit around -0.29 to -0.30 percent per degree.

Formula used below: loss percent = (cell temperature - 25) x |coefficient|. The coefficient is from the module datasheet.

Cell temperatureCoefficientInstantaneous loss
45C, warm spring day-0.29 %/CAbout 5.8 percent
55C, typical summer roof-0.29 %/CAbout 8.7 percent
65C, hot afternoon-0.29 %/CAbout 11.6 percent
70C, very hot roof-0.29 %/CAbout 13 percent
70C, older PERC module-0.36 %/CAbout 16 percent

What a normal heat derate looks like

A useful sanity check is the performance ratio: actual production divided by what the system should produce at the measured irradiance and temperature. A system running near its expected ratio in hot weather is derating normally. A system well below it, especially in cool conditions, is not.

  • The whole array loses output together, not one panel or one string.
  • The drop tracks the weather: worst in the early afternoon, better on cloudy days and in the evening.
  • The shape of the daily curve stays normal, just lower at the peak.
  • The same month across two years looks similar when the weather is similar.
  • Production recovers in cool, clear winter conditions without any repair.

The signs that point at a fault instead

Two conditions deserve special attention because they look like heat derate but are not. The first is one underperforming module while its neighbours are normal, which points at a device, a connection, or a shading change. The second is a system that keeps underperforming in cool months, which is a fault that has nothing to do with temperature.

Heat derate is array-wide and reversible. Faults are not.

PatternNormal heat derateWorth a diagnostic
ScopeWhole array moves togetherOne panel, one string, or one microinverter
TimingWorst at peak heat, recovers afterPersists in cool weather and in the evening
Curve shapeNormal shape, lower peakFlat segments, dropouts, or a hard cutoff
ComparisonMatches neighbours with similar systemsClearly below a neighbour's identical system
HistorySimilar year over yearProgressive decline across several months
WarningsNoneDevice alerts, ground fault, arc fault, or inverter codes

What a homeowner can check, safely

  • Compare the same month across two years, not two consecutive months.
  • Note whether the drop is array-wide or device-specific in the monitoring app.
  • Look for any alert or code in the app or on the inverter display.
  • Check for new shading: a tree that grew, a new structure, or debris.
  • Photograph the inverter display during peak afternoon heat.

When to book a diagnostic

Book a diagnostic if the loss is not array-wide and smooth, if it persists in cool weather, if any device reports an alert, or if the same month across two years is clearly worse. Otherwise, treat a modest peak-hour drop in July and August as the cost of a Florida roof and compare again in cooler months.

If the technology is older, ask the service provider to check the module datasheet coefficient against what the system is actually doing. A 2015 PERC array and a 2026 TOPCon array should not be judged against the same expectation.

Frequently asked questions

Roughly the module's temperature coefficient multiplied by the degrees the cells sit above 25C. On a hot roof near 65C to 70C, that is about 12 to 13 percent during peak hours for a modern N-type module, and more for older PERC products.

Property-specific next step

Request a Production Review

Send the monitoring history, the inverter display photo and the system age. We can review the request and check whether a licensed service partner covers your equipment.

Palm Beach Solar plans and coordinates the project. The selected licensed installation or service partner evaluates, quotes, and performs work under its own contract, licensing, and warranty terms.